Blackweb BWA18AV007 Manual 6-Device Blackweb Universal Remote BWA18AV007 Manual Universal Remote with Private Listening Instrutions Programming Pairing Troubleshooting

Blackweb BWA18AV007 Manual

Blackweb Learning Remote Manual

Blackweb Universal Remote BWA18AV007 Manual

Blackweb Universal Learning Remote Manual

GETTING STARTED BATTERIES

Thank you for choosing the Blackweb Universal Remote Control and Wireless Audio Transmitter. This remote control can operate a wide range of electronic devices, works across most brands and models, and comes pre-programmed to operate many Samsung TVs (see the Programming Your Remote sections if your device is not compatible). Your remote can control up to 6 devices and is remarkably easy to set up. To get started, please install two AA alkaline batteries (not included) as shown below.

Installing the Batteries

  1. Remove the battery cover.
  2. Insert the batteries as shown.
  3. Snap the battery cover back into place.

Battery Precautions

  • Do not mix old and new batteries.
  • Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
  • Always remove old, weak or wornout batteries promptly and recycle or dispose of them in accordance with local and national regulations.

Low Battery Indicator

If while using the remote, the button’s red indicator light flashes 3 times, this indicates the batteries
need to be replaced. Please replace the batteries as soon as possible when this indication occurs.

Code Saver

When changing the batteries of your remote, please do so quickly. You have up to 20 minutes to change the batteries in your remote without losing the programmed codes.

Battery Saver

To conserve battery power, the remote will automatically turn off if any button is pressed for more than 60 seconds (except during programming).
This feature is helpful in the event that the remote is stuck in a location where the buttons remain depressed, such as between sofa cushions.

TROUBLESHOOTING

If you are having issues with the universal remote:
The tips below can help you solve problems and answer questions you
may have with your remote control. In general, always make sure:
1) The remote is in the correct device category mode (TV, SAT/CBL,
STREAM, B-RAY/DVD, AMP, AUX); this tells the remote which device
to operate.
2) The batteries are fresh and properly installed.
3) To remove any obstacles between the remote and the device, and that
you’re aiming the remote at the device’s IR sensor.
The remote can’t be programmed to operate my device.
• If you’re using the Direct Code Entry method to enter the codes for your
brand and the device is still not functioning properly after trying all the
code options, try the Auto Code Search method.
• To control combo devices like TV/VCRs or TV/DVDs, you must program
the individual corresponding device buttons to control each part of the
combo unit.
Some of the buttons of the remote are not supported or working
properly on my device.
• It’s possible the code that you programmed is not fully compatible with
your device. Try selecting the next code from the options available for
the category and brand of your device.
• There may be some buttons from your device’s original remote that are
not supported.
• You may have pressed an invalid button for the device category mode the
remote is in.

The remote will not change the channels on my device.
• Make sure the remote is in the correct device category mode (TV,
SAT/CBL, STREAM, B-RAY/DVD, AMP, AUX) that controls the channels.
• Try pressing the ENTER button after you enter a channel number (a
requirement with certain models and brands of TV and/or Cable/Satellite
boxes).
The remote will not adjust the volume on my device.
• Make sure the remote is in the correct device category mode (TV, SAT/
CBL, STREAM, B-RAY/DVD, AMP, AUX) that controls the volume.
My device’s menu or app hub does not appear.
• Menu and app hub access isn’t supported for all brands. You may need
to use your original remote control to access the menu functions and/or
app hub for some devices.
My remote’s light is blinking
• If while using the remote the indicator light flashes 3 times, this indicates
the batteries need to be replaced.

If you are having issues with the Private Listening feature:
• Ensure the batteries in your remote are working and the audio transmitter
is connected to a power source.
• Ensure the television’s selected audio output is configured to send the
audio to the audio transmitter.
• Ensure the television’s audio output volume is not too low or muted
• Ensure the headphones are plugged in properly.
• Raise the headphone volume using the volume control on the right
side of the universal remote.
If the LED indicator is continuously ashing:
Your universal remote and audio transmitter are already paired to work
together out of the box. The LED indicator on your audio transmitter will
be steady blue when paired properly and will flash 1-3 times when the
Private Listening feature is activated or deactivated. If you notice the
LED indicator is continuously flashing, it means that the audio transmitter
and universal remote are not paired. In that case, please follow the
instructions below.

Follow these instructions only if the LED indicator is continuously
ashing on the audio transmitter
PAIRING MODE
To enter pairing mode:

  1. Connect the audio transmitter to a
    power source.
  2. Plug the headphones into the universal
    remote.
  3. Locate the PAIRING button on the
    bottom of the audio transmitter.
  4. Locate the HEADPHONE MUTE
    button on the universal remote.
  5. With the devices no further than 18”
    apart, hold down both buttons for 5
    seconds.
    When your devices are paired there will
    be a short beep in the headphones and
    the audio transmitter’s LED indicator will
    become steady blue.

POWER
Turns your device On/Off and also serves as an indicator when the remote is being programmed

INPUT
Switches between the sources connected to your TV

DEVICE CATEGORIES
Use these buttons to select the device you want to control

PROGRAM
Use to put your remote in programming mode

GUIDE
Use to access the guide of satellite and cable set-top boxes

APPS
Use to access your smart TV’s apps (if supported)

BACK
Return to the previous menu or screen

A, B, C, D BUTTONS
Use to access device shortcuts for additional features or custom apps on your device (if supported)

INFO
Use to access on-screen content description and information

PROGRAMMING YOUR REMOTE DIRECT CODE ENTRY

Programming your remote is as easy as 1, 2, 3
Before beginning, please make sure that the device you want to control is powered on and follow these three simple steps.
NOTE: Press to exit at any time

Press and hold the button until the button lights up red.
The button’s red indicator light remains on.

NOTE: The Blackweb universal remote comes pre-programmed to operate
many Samsung TVs.

Select the device you want to program
from the Device Categories:
The button’s red indicator light blinks once and remains on

Enter the 4-digit code from the included list for the category and brand of your device.
The button’s red indicator light
shuts off if a valid code was entered.
If the button’s red indicator light flashes and remains on after entering four digits, that means an invalid code was entered. In that case, check the list again and re-enter the code.
NOTE: Test the remote with the device to make sure the buttons work as expected. If some of the buttons/ features don’t work, try a different code on the list. Repeat this process for each device you wish to control.

PROGRAMMING YOUR REMOTE AUTO CODE SEARCH

It’s recommended to program your remote by using the Direct Code
Entry method, however if with that method you were not able to find
a code that is compatible with your device, you may try the Auto Code
Search method below:

  1. Power on the device that you want to control.
  2. Press and hold the button until the button lights up red.
    The button’s red indicator light remains on.
  3. Select a device from Device Categories you would like to control.
    The button’s red indicator light blinks once and remains on.
    NOTE: Please refer to the list below if you are unsure about the device category.
    • TV: TV, TV/DVD and other TV combinations
    • SAT/CBL: Satellite, Cable, DVR, and other set-top boxes
    • STREAM: Roku, Apple TV, Xbox, and other streaming media players*
    • B-RAY/DVD: Blu-ray Players and DVD Players
    • AMP: Sound Bars, Audio Receivers, and other audio devices
    • AUX: VCRs, Digital Frames, and devices not found on the code list
    *Compatible with Apple TV® and most Roku® devices; not compatible with Roku® Streaming Stick®,
    Amazon® Fire TV and any voice-search features
  4. Point the remote at the device you wish to control and then press and
    hold the OK button until the device turns off. The button’s red
    indicator light will blink as the codes are being tested.
  5. When the device turns off, immediately release the OK button to lock
    in the code. The button’s red indicator light will turn off. Test the
    remote with the device to make sure all the buttons work as expected.
    If some of the buttons/features don’t work, repeat the process or try
    the Direct Code Entry method.
    NOTE: It may take over 10 minutes to scan through all the possible codes for
    your device. If during the Auto Code Search you have either accidentally or
    deliberately released the OK button, you may repeat steps 1 through 5 above
    to resume the code search where it left off.
    After the Auto Code Search has exhausted all available codes for the selected
    category, the remote’s button’s red indicator light blinks three times and
    turns off. If none of the codes worked with your device, try the Direct Code
    Entry method.

FAVORITE CHANNELS

For easy access to up to 10 of your favorite channels, follow the steps below.

  1. Select a device from Device Categories that controls the channels.
    The button’s red indicator light will blink once.
  2. Press and hold the button until the button lights up red.
    The button’s red indicator light remains on.
  3. Press the button. The button’s red indicator light blinks once
    and remains on.
  4. Select the button (0 – 9) that you will use for storing your favorite
    channel. The button’s red indicator light blinks once and remains on.
  5. Enter the channel number you wish to program as a favorite channel.
  6. Press the button, the button’s red indicator light will turn off
    and the channel is saved.
    NOTE: To change a stored favorite channel, repeat steps 1-6 above.
    To Access Your Favorite Channels:
  7. Press the button. The button’s red indicator lights up and
    remains lit.
  8. To access the favorite channel, press the programmed button for that
    channel (0-9). The button’s red indicator light blinks, then turns off
    as the command is sent.

VOLUME LOCK

Use this feature to lock a device to the remote’s volume control. For
example, the remote can be in TV mode while the volume buttons control
your sound bar.
Enabling Volume Lock:

  1. Press and hold the button until the button lights up red.
    The button’s red indicator light remains on.
  2. Select a device from Device Categories that you want to lock to the
    remote’s volume control. The button’s red indicator light blinks
    once and remains on.
  3. Press the VOL+ button. The button’s red indicator light blinks once
    and remains on.
  4. Press the OK button. The button’s red indicator light will blink twice
    and turn off.
    Disabling Volume Lock:
  5. Press and hold the button until the button lights up red.
    The button’s red indicator light remains on.
  6. Press the VOL- button. The button’s red indicator light blinks
    once and remains on.
  7. Press the OK button. The button’s red indicator light will blink twice
    and turn off.
    NOTE: On most newer HDMI-connected devices, the Volume Lock feature may
    be unnecessary as this feature is already built-in.

CHANNEL LOCK

Use this feature to lock a device to the remote’s channel control. For example,
the remote can be in TV mode while the channel buttons control your
satellite or cable box.
Enabling Channel Lock:

  1. Press and hold the button until the button lights up red.
    The button’s red indicator light remains on.
  2. Select a device from Device Categories that you want to lock to the
    remote’s channel control. The button’s red indicator light blinks
    once and remains on.
  3. Press the CH+ button. The button’s red indicator light blinks once
    and remains on.
  4. Press the OK button. The button’s red indicator light will blink twice
    and turn off.
    Disabling Channel Lock:
  5. Press and hold the button until the button lights up red.
    The button’s red indicator light remains on.
  6. Press the CH- button. The button’s red indicator light blinks once
    and remains on.
  7. Press the OK button. The button’s red indicator light will blink twice
    and turn off.
    NOTE: On most newer HDMI-connected devices, the Channel Lock feature
    may be unnecessary as this feature is already built-in.

CODE IDENTIFICATION & FACTORY RESET

Code Identification:
To identify any of your programmed codes, follow the steps below.

  1. Press and hold the button until the button lights up red.
    The button’s red indicator light remains on.
  2. Select a device from Device Categories that you would like the code
    for. The button’s red indicator light blinks once and remains on.
  3. Press the button. The button’s red indicator light blinks once
    and remains on.
  4. Press the button. Count the number of times the button’s red
    indicator light flashes. This is the number corresponding to the first
    digit of the code. If the button does not flash, the corresponding
    code number is 0. Repeat the process by pressing the , and
    buttons for the remaining digits.
  5. Press the button to exit.
    NOTE: Press to exit at any time.
    Reset to Factory Settings:
  6. Press and hold the button until the button lights up red.
    The button’s red indicator light remains on.
  7. Press the button. The button’s red indicator light blinks once
    and remains on.
  8. Press the OK button. The button’s red indicator light will flash twice
    and the remote will revert to factory settings.

ABOUT PRIVATE LISTENING

When you want to watch without disturbing others, you can use the
universal remote’s Private Listening feature by inserting headphones
into the universal remote and transmitting the sound from the audio
transmitter attached to your television.

  • TV
  • AUDIO TRANSMITTER
  • Approximately 30 ft maximum wireless range
  • STEREO HEADPHONES
  • UNIVERSAL REMOTE

GET TO KNOW YOUR AUDIO TRANSMITTER

  • (L) OUT (RCA audio output)
  • (R) OUT (RCA audio output)
  • POWER (Micro USB port, 5V/300mA)
  • STEREO IN
  • OPTICAL IN (S/PDIF)
  • OPTICAL OUT (S/PDIF)
  • LED INDICATOR
  • PAIRING BUTTON

CAUTION: Don’t press this button unless you want to unpair the remote
from the audio transmitter (your universal remote and audio transmitter
are already paired to work together out of the box).
For more information, please refer to “PARING MODE” in Troubleshooting.

HOW TO SET UP YOUR AUDIO TRANSMITTER

1 Connect the supplied USB charger to the audio transmitter’s USB port
labeled “POWER”.

POWER / BACK / USB CHARGER / WALL OUTLET

When connected to a power source, the audio transmitter’s LED indicator turns solid blue.

NOTE: A steady blue light indicates that the audio transmitter is paired to the remote (by default). If the LED indicator is continuously flashing, it indicates that the audio transmitter and remote are not properly paired (please refer to “Pairing Mode” in Troubleshooting).

  1. Connect the white and red plugs of the supplied RCA/3.5mm audio cable
    to the (L) and (R) AUDIO OUT on your television’s connection panel.
    NOTE: Ensure the cables are NOT plugged into the TV’s audio input.
  2. Connect the 3.5mm stereo plug to the audio transmitter’s “STEREO IN”
    port as shown below.

NOTE: The Private Listening feature DOES NOT SILENCE the audio
that may be playing through your television’s built-in speakers, sound bar or
other connected A/V equipment.
• You can use the equipment manufacturer’s remote or the universal remote’s
volume, mute or power controls to silence the audio.
• On some televisions, you may need to manually switch the audio output
from the built-in speakers to the connected audio transmitter equipment.
Please consult your equipment manufacturer’s manual for instructions.

If you have a sound bar or other audio equipment already connected to
your television’s audio jacks, you can use the audio transmitter’s audio
passthrough connection labeled “(L) OUT” and “(R) OUT” to connect
to your other audio equipment.

Using an S/PDIF optical cable for digital audio
For televisions equipped with an S/PDIF optical output, you may connect
an optical cable (not included) to the TV’s connection panel. Connect the
other end of the optical cable into the audio transmitter’s “OPTICAL IN”
port (supports 96kHz/24bit).

If you have a sound bar or other audio equipment already connected to
your television, you can use the audio transmitter’s audio passthrough
connection labeled “OPTICAL OUT” to connect to your other audio
equipment.
NOTE: When an audio source is connected to the audio transmitter’s
“STEREO IN”, the optical ports will not function.

PRIVATE LISTENING THROUGH YOUR REMOTE

You may control the headphone‘s audio volume with the HEADPHONE
VOLUME buttons located on the right side of the remote.
To mute and unmute the headphone audio, press the HEADPHONE
MUTE button located on the right side of the remote.

The buttons below ARE NOT used for controlling the
headphone’s audio volume.

Activating Private Listening
To activate the universal remote’s Private Listening feature, simply plug
in a pair of headphones into the 3.5MM HEADPHONE JACK located on
the left side of the remote.

After inserting the headphones, the audio transmitter’s LED indicator will
flash three times and play a beep in the headphones indicating when the
Private Listening feature has been activated.

Deactivating Private Listening
To deactivate the universal remote’s Private Listening feature, simply
unplug the headphones.

CAUTION: DON’T FORGET TO UNPLUG THE
HEADPHONES OR IT WILL DRAIN THE
REMOTE’S BATTERIES.

When the headphones are unplugged, the audio transmitter’s LED indicator
will flash once to indicate that the Private Listening feature has been
deactivated.

FCC INFORMATION

This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.

LIMITED 90DAY WARRANTY

Product Type: Universal Remote Control & Wireless Audio Transmitter
Territory: United States / Canada
Warranty Period: 90 (Ninety) days
To obtain warranty service:
• Call the Customer Support number or go to our website portal (shown
below) to receive an SRO number.
• Include the dated receipt or proof of purchase within the package.
• Prepay all shipping costs to the Authorized Service Center below
(remember to insure your return).
• Include a return shipping address (no P.O. Boxes), telephone contact
number, and the defective product within the package.
• Be sure to write your SRO number on the outside of the package.
• Describe the defect or reason you are returning the product.
Customer Support:
• (877) 907-7010 (Monday-Friday, 8AM – 10PM EST)
• www.myblackwebremote.com (click on “Product Support”)
Your product will be repaired or replaced, at our option, for the same or
similar model of equal value if examination by the service center determines
the product is defective. Products received damaged as a result of shipping
will require you to file a claim with the carrier.
Authorized Service Center
Customer Service – Dept. 36
400 Kennedy Drive
Sayreville, NJ 08872
Warranty service not provided
This warranty does not cover damage resulting from accident, misuse, abuse,
improper installation or operation, lack of reasonable care and unauthorized
modification. This warranty is voided in the event any unauthorized person
opens, alters or repairs this product. All products being returned to the
authorized service center for repair must be suitably packaged.
NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, OTHER THAN THOSE EXPRESSLY DESCRIBED
ABOVE SHALL APPLY. DISTRIBUTOR FURTHER DISCLAIMS ALL WARRANTIES
AFTER THE EXPRESS WARRANTY PERIOD STATED ABOVE. NO OTHER EXPRESS
WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR ENTITY WITH
RESPECT TO THE PRODUCT SHALL BE BINDING ON DISTRIBUTOR. REPAIR,
REPLACEMENT, OR REFUND OF THE ORIGINAL PURCHASE PRICE – AT
DISTRIBUTOR’S SOLE DISCRETION – ARE THE EXCLUSIVE REMEDIES OF THE
CONSUMER. IN NO EVENT WILL DISTRIBUTOR OR ITS MANUFACTURERS BE
LIABLE FOR ANY INCIDENTAL, DIRECT, INDIRECT, SPECIAL, PUNITIVE OR
CONSEQUENTIAL DAMAGES (SUCH AS, BUT NOT LIMITED TO, DAMAGES
FOR LOSS OF PROFITS, BUSINESS, SAVINGS, DATA OR RECORDS) CAUSED
BY THE USE, MISUSE OR INABILITY TO USE THE PRODUCT. EXCEPT AS STATED
26
HEREIN, NO OTHER WARRANTIES SHALL APPLY. NOTWITHSTANDING THE FOREGOING,
CONSUMER’S RECOVERY AGAINST DISTRIBUTOR SHALL NOT EXCEED THE PURCHASE PRICE
OF THE PRODUCT SOLD BY DISTRIBUTOR. THIS WARRANTY SHALL NOT EXTEND TO ANYONE
OTHER THAN THE ORIGINAL CONSUMER WHO PURCHASED THE PRODUCT AND IS NOT
TRANSFERABLE.
Some countries, states or provinces do not allow the exclusion or limitation of incidental
or consequential damages or allow limitations on warranties, so limitation or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may have other
rights that vary from state to state or province to province. Contact your authorized retailer
to determine if another warranty applies.

blackweb universal remote instructions

blackweb remote instructions

blackweb remote manual

Programming Blackweb Remote Steps Universal Blackweb Remote Program Setup Manual Instructions Codes List

Thank you for choosing the Blackweb Universal Remote Control. This Blackweb remote control can operate a wide range of electronic devices and works across brands and models.

Blackweb Universal Remote Instructions

Programming Blackweb Remote

Blackweb Universal Remote Instructions

Reading guides:

  1. Check Device Blackweb Remote PCL-X, PCL1, PCL2 or PCL3
  2. Program Blackweb Remote method and steps
  3. Please checking or search the Blackweb Remote Codes List at the end of post for enter code Programming!

Checking Device Model Number

Make

How do I find the 4-digit code for my TV?

To find your code, enter your device information

Method 1 Auto Code Entry Steps

How to Program a Blackweb Remote without a Code

Programming your remote is as easy as 1,2,3

How to pair a Blackweb remote

  • Press and hold the “Program” button until the “Power”  button lights up red.
  • The “Power”  button’s red indicator light remains on.
  • Select the device you want to program from the Device Categories:
  • The “Power” button’s red indicator light blinks once and remains on.
  • Press the OK button until the “Power ” button “off” , it will auto search the right code.
  • The “Power” button’s red indicator light shuts off if a valid code was entered.
  • If the “Power” button’s red indicator light is still on that means an incorrect code was entered. In that case, check and do the steps again.

How do I program a universal remote without a code?

Method 2 Enter Codes

Use the code finder tool below to quickly find compatible Blackweb codes for the different devices in your home. If there are several codes available for your device, test each one and select the code that is the most compatible with your device.

To find your code, enter your device information, Blackweb universal remote codes list:

Please Checking your Blackweb Remote Codes List after steps

Where is the code list?

My blackweb remote codes list checking from myblackwebremote codes

Detail checking from myblackwebremote.com

Attentions: the website speed is not very fast, checking the code at the end of this post is faster!

such as myblackwebremote tv codes

Programming your remote is as easy as 1,2,3

How to activate Blackweb remote

  • Press and hold the “Program” button until the “Power”  button lights up red.
  • The “Power”  button’s red indicator light remains on.
  • Select the device you want to program from the Device Categories:
  • The “Power” button’s red indicator light blinks once and remains on.

  • Enter the 4-digit code from the included list for the category and brand of your device.
  • The button’s red indicator light shuts off if a valid codes for Blackweb remote was entered.
  • If the  button’s red indicator light is still on that means an incorrect Blackweb controller codes was entered. In that case, check the list again and re-enter the code.

Blackweb Remote Programming Tutorials

Your Blackweb remote can control up to 6 devices and is remarkably easy to set up.  These video tutorials will give you step-by-step instructions for programming the remote control. Watch and learn!

Blackweb 6 device universal remote codes

Blackweb Universal Remote Codes

Blackweb Remote Codes List

Blackweb TV Remote Codes

BrandBlackweb TV Remote Codes PCL1
ACER1163, 1817
ADMIRAL0135, 2120, 2058, 0001, 2439, 0020
ADVENT2354, 0176, 0167, 1181, 2434, 1160, 0116
AFFINITY2077, 2078
AIWA3009, 1949, 2423, 2428, 0196
AKAI0214, 1148, 1137, 2487, 2488, 2494, 2012, 0076, 1138, 2415, 1139, 2451, 0231
AOC2091, 2063
APEX DIGITAL2497, 2499, 0424, 2431, 1796, 0214, 2061, 0436, 0215, 0216, 0949, 2139, 1132, 0445
ARIO2061
ATVIO2046
AUDIOVOX0053, 2290, 1146, 1165, 2418, 1019, 1164
AURIA0009, 1179, 2504
AURORA1826
AXION0177
BANG & OLUFSEN0190
BENQ2044, 0101, 0083, 1150, 0081
BLUESKY0144, 1155
BROKSONIC0135, 2103, 0147, 2228, 2436, 0237
CAPEHART0175, 2404
CELERA0214
CHANGHONG2431
CITIZEN0004, 0008, 0009, 0001, 0042, 0053, 2406, 0244, 0252
COBY1796, 2356, 1804, 1863, 2448, 2452, 1805, 1813
COLORTYME0004, 0009, 0010
CONTEX2466
CORNEA0050
CRAIG0042, 0053
CROSLEY0062
CTX0020
CURTIS2067, 0077, 2077, 2046, 2466, 3030, 2061, 0130
CURTIS MATHES0105, 3022, 2465, 1847, 0004, 0015, 0009, 0001, 2435, 0249
DAEWOO3023, 0004, 0126, 0017, 0127, 0018, 0009, 0019, 2152, 0010, 0080, 2209, 3022, 0042, 0043, 2406, 2094, 0039, 0100, 0130, 0138, 0140, 0244, 0252, 0444
DAYTRON0004, 0009
DELL0028, 2187, 2358, 0132, 2363, 2377
DIAMOND VISION0092
DIGIMATE1017
DIGISTAR0165, 1160, 0167, 0118, 2290, 1020, 1152, 0116, 1019, 1151
DISNEY0135, 0158
DISTAR2085
DUKANE0059, 0072
DUMONT0121
DURABRAND0135, 0198, 0157, 0217, 0189, 0133, 0153, 2449
DYNEX1171, 2461, 2351, 0135, 1181
ELECTROHOME0004, 0009, 0022, 3105, 2357, 0003
ELECTRON2067
ELEMENT3538, 1025, 2468, 1820, 1173, 3109, 3000, 2464, 2492, 1821, 2467
EMERSON2324, 3110, 2454, 2455, 2472, 3109, 2423, 2467, 2477, 0004, 0198, 1173, 1141, 1172, 3014, 3022, 2471, 0023, 0027, 0032, 0034, 0037, 0039, 0040, 0045, 0130, 0179, 0231, 0237, 0249, 0252, 0259
ENVISION2504, 2095, 0004, 0074, 0009, 2369, 2091, 1009
EQD1179, 2504
ESA0198, 0189
FAVI0077
FISHER2440, 0049, 2210, 2254, 2360, 0012, 0180, 1957
FLUID1025, 1026, 1027
FUJITSU2011, 0051, 3108, 1178, 0197, 1006
FUNAI1877, 0198, 1949, 0051, 0042, 0053, 2423, 2426
GATEWAY2116, 0046
GE2433, 0198, 0214, 0048, 0004, 0044, 2057, 0015, 2359, 0087, 0009, 0022, 0052, 3105, 2357, 0003, 0054, 0125, 0164
GFM0198, 3109
GOLDSTAR0004, 2117, 3107, 1949, 0338, 0009, 0080, 2254, 2423, 0012, 0057, 0156, 1957
GPX2421
GVISION1005
HAIER2502, 0217, 0077, 3001, 0216, 0157, 1147, 3106, 0081, 0935
HANNSPREE2097, 1831, 1832
HP1004, 1015
HISENSE3537, 1173, 0182, 2463, 2060, 0077, 2464, 0004, 0216, 0073, 1016, 1176, 2503
HITACHI0088, 0419, 0012, 0061, 0091, 0137, 0139, 0142, 0179, 1002, 1957
HKC2100
HYUNDAI1134
ILO2451, 0189, 2012, 2141, 1024, 1023, 0146, 2442, 1139
INFOCUS0094
INITIAL0146, 2430, 2442, 2443
INSIGNIA/ROKU3531, 0135, 0133, 0198, 1160, 0167, 0217, 0103, 3002, 2334, 1180, 1175, 2422, 2426, 2444, 2445, 0029, 0116, 1407, 1181
INTEGRA0181
INTEQ0111, 0038, 0121
ISYMPHONY0077, 0085
JBL0062
JC PENNEY0004, 2057, 0015, 0087, 0008, 0009, 0030, 2254, 0022, 0052, 0012, 0054, 1957
JENSEN0133, 0004, 0009
JVC2446, 0160, 0065, 0026, 0067, 2011, 0069, 0141, 2254, 2459, 0012, 0197, 1957
KAWASAKI2424
KENWOOD0004, 0009
KLH0214
KTV0014, 0070, 0021, 0042, 0053
LASONIC2147, 0210, 2429
LEGEND2061, 1160, 0116
LG3534, 0004, 2098, 0155, 2254, 0338, 0009, 0012, 0057, 0134, 0156, 1957, 2492
LOEWE0211, 0062
LOGIK0001, 0031, 0094
LUCE1022, 0055
LXI0004, 0015, 1949, 0009, 0031, 2423, 0062
MAG2099
MAGNAVOX2477, 0899, 1174, 1133, 2426, 2091, 0198, 0062, 0235, 2120, 1772, 0183, 2427, 2439, 0207
MAJESTIC0001, 0031, 0094
MARANTZ0004, 0009, 1819, 0062, 0181
MAXENT2116, 1916, 0046
MEMOREX0051, 0004, 2103, 0009, 2228, 0001, 1025, 1007, 2440
MGA0004, 0009, 0051, 0141, 2254, 0022, 0012, 0180, 1957
MIDLAND2057, 0015, 0107, 0031, 0038, 0054, 0121
MINTEK0146
MITSUBISHI2086, 0151, 0005, 0004, 0009, 0051, 0141, 0022, 2319, 0180
MONIVISION0036
MYRON & DAVIS0212
NAXA3021, 0077
NEC0004, 0095, 0009, 0010, 2359, 0141, 1819, 3105, 2357, 1384, 0003, 0181, 0249
NEXUS1173, 2492
NEXXTECH0167, 1052
NIKO0004, 0058, 0009, 2406, 1143
NORCENT0056, 0216, 0043
OLEVIA2347, 1012, 1156, 2450, 1142
ONKYO1884
OPTOMA2350, 1028
OPTONICA0095, 2058, 0020
ORION0135, 0035, 0111, 0038, 0121
PANASONIC3005, 2484, 0381, 2470, 3024, 2472, 0381, 0003, 0054, 0062, 0171, 1182, 1989
PHILCO0183, 0198, 0004, 0075, 0008, 0068, 2359, 0009, 0011, 0141, 3105, 1962, 2357, 1158, 0003, 0235
PHILIPS3535, 1154, 2477, 2495, 1141, 1772, 0205, 2091, 0003, 0062, 0081, 0086, 0154, 0208, 1776, 0199, 0200, 0206, 0207, 1149, 0183, 2427, 2439, 2120, 0204
PIONEER0185, 0009, 0072, 0004, 1879, 1819, 2396, 3104, 0090, 0179, 0181
PIVA2284, 2441
PLANAR1007
POLAROID2099, 1025, 0214, 2466, 2063, 1160, 2499, 0133, 0173, 2290, 1136, 0029, 0116, 1019, 1169, 1177
PRECISION0166
PRIMA0165, 1160, 0176, 0167, 2290, 0116, 1019
PRINCETON GRAPHICS0099, 2058, 0020
PRISM0054
PROSCAN2467, 2480, 1174, 0000, 1173, 3027, 2069, 0077, 2077, 2046, 2078, 0015, 0162, 0163
PROTON0004, 0175, 3102, 0009, 2254, 0093, 3103, 2404, 1010, 0186, 0192, 1957
PROTRON1157, 1017
PROVIEW1025, 1026, 1027
PYLE1816
QUASAR0170, 1820, 2057, 0070, 3024, 2359, 3105, 2357, 0381, 0003, 0054, 0062, 0171
RADIOSHACK0004, 0095, 1949, 0048, 0009, 3024, 0041, 2254, 0042, 0053, 2423, 2433, 0012, 1957
RCA0048, 3027, 2433, 0004, 2357, 2067, 2046, 2069, 2078, 2077, 0077, 2209, 0191, 0102, 0003, 0054, 0096, 0100, 0113, 0125, 0129, 0179, 0187, 0188
REALISTIC0004, 0095, 1949, 0048, 0009, 3024, 0041, 2254, 0042, 0053, 2423, 0012, 1957
ROKUTV2491
RUNCO0111, 0038, 1819, 0121, 0181
SAMPO0004, 0219, 0175, 2116, 0009, 2254, 2404, 0012, 0046, 0124, 1957
SAMSUNG3528, 2481, 2482, 2355, 0007, 0012, 0104, 0106, 0172, 1773, 1957
SAMTRON0105
SANSUI2466, 2103, 0189, 1181, 2456, 2485, 2495, 2496, 2228, 2471
SANTECA0194
SANYO0110, 2458, 1181, 2457, 0012, 0108, 0180, 1833, 1834, 1957, 2000
SCEPTRE0149, 1167, 1132
SCOTT2012, 0004, 0024, 0035, 0009, 0051, 0042, 0053, 1139, 0237
SEARS0004, 2103, 0015, 0009, 0051, 2254, 2426, 0012, 0062, 0180, 1957
SEIKI1822, 2478, 2498
SHARP2464, 2491, 0223, 2352, 2489, 0004, 0006, 0020, 0122, 0123
SILO2486
SKYWORTH3011, 3010, 3003
SONY3536, 2483, 2462, 2438, 0002, 2323, 0071, 0033, 0152
SOUNDESIGN0004, 0008, 0009, 0051, 0042, 0053
SOVA1003, 2411
SOYO1130, 1131
STARLITE0053
SUNBRITE TV2347, 0149
SUPERSCAN2426, 0079, 0112
SUPERSONIC3021, 2104, 2421
SV20002426
SVA0216, 0212
SYLVANIA0189, 2324, 0135, 2426, 2364, 0198, 1141, 1172, 3101, 3014, 0004, 0075, 1949, 0008, 0068, 0009, 0141, 0161, 2423, 0062
SYMPHONIC0189, 2426, 0198, 0024, 1949, 0053, 2423
SYNTAX1027, 2450, 1142
TANDY0020
TATUNG2141, 2044, 3105, 2357, 0003, 0081
TCL/ROKU3532, 2493, 2479, 3004, 2490
TECHNICS2057, 0054
TMK0004, 0009, 0249
TOSHIBA0109, 2470, 0159, 2103, 0095, 0117, 3024, 0141, 1819, 2254, 2432, 2435, 2447, 0012, 0120, 0178, 0181, 1848, 1957
TRUTECH0198, 1029, 1145, 2419
VENTURER1183
VIDTECH0004, 0005, 0009
VIEWSONIC2369, 1179, 2504, 2460, 2116, 0072, 1144, 1014, 0046
VIORE2096, 3021, 3030, 0077, 1856, 1818, 1018
VIZIO3533, 2472, 2045, 2501, 2473, 0143, 2476, 2474, 0081, 1168, 1169, 0033, 2475
WARDS0004, 0024, 0075, 0095, 0087, 0008, 0068, 0009, 0119, 0001, 0051, 0052, 0062
WESTINGHOUSE2480, 3098, 3099, 0013, 2061, 0077, 0114, 1814, 2456, 0136, 1949, 0080, 2209, 3022, 2423, 0100, 0130, 0138, 1008
YAMAHA0004, 0005, 0009, 3024, 0170
ZENITH2492, 2459, 0338, 0004, 0038, 0064, 1949, 0078, 0009, 2152, 2228, 0001, 1857, 0153, 0131, 2406, 2423, 2425, 2427, 2435, 2453, 0023, 0039, 0091, 0121, 0134, 0138, 0252

Blackweb TV/DVD Player Combo Universal Remote Codes

BrandDVD Codes
AUDIOVOX2418
BROKSONIC0394, 2103, 1780
COBY1091
DURABRAND0405
EMERSON0456, 1877
FUNAI0456, 1877
GPX0944
HAIER0935
INSIGNIA0456, 1877, 1406, 1408, 1135, 1407
JVC0923, 2342
MAGNAVOX1877, 0456
MAXENT1916
MEMOREX0394, 2103, 1780
PANASONIC0456, 0437, 2144, 2174, 0148
PHILIPS0204, 2081, 1975, 0456, 1877
SAMSUNG0942
SANSUI0394, 2103, 1780
SUPERSONIC0944
SYLVANIA0456, 1877
SYMPHONIC0456, 1877
TOSHIBA0394, 0924, 2103, 2346, 1780

Blackweb Blu-Ray Universal Remote Codes

Brand NameBlu-Ray Codes
Funai2378
HITACHI0419, 0150, 0225
HP1810
INSIGNIA1871, 0899, 1874
JVC1789
LG1981, 1980, 2281
MAGNAVOX1934, 1877, 2381, 2287
ONKYO1893
OPPO1855, 2022
PANASONIC1399, 1925, 1923
PHILIPS1976
PIONEER1378
SAMSUNG2399, 1099, 0454, 1908, 2030, 1906
SANYO2273
SHARP1952, 2019
SHERWOOD1824, 1809
SONY1934, 1935, 1936
SYLVANIA3027, 2013, 1878
TCL1825
TOSHIBA1852, 1850, 1851
VIZIO2024, 1770
YAMAHA2017

programing blackweb remote

blackweb remote manual

blackweb remote auto search

Blackweb remote control not working

program blackweb remote

Programming Blackweb Remote

bwa21av020c

blackweb remote tv codes

blackweb remote control codes

myblackwebremote codes

blackwebremote

blackweb tv remote codes

blackweb remote codes for hisense tv

blackweb universal remote codes for hisense

blackweb universal remote tv codes

blackweb universal remote codes for vizio tv

blackweb remote codes for samsung tv

blackweb remote codes for lg tv

blackweb remote codes for roku

blackweb tv codes

blackweb universal remote codes for dvd player

Blackweb Remote Setup

blackweb soundbar remote codes

black web universal remote

blackweb remote code for amazon fire stick

blackweb remote codes for vizio

my blackweb remote codes

www blackweb remote

codes for blackweb universal remote

Blackweb Universal Remote Programming

blackweb remote codes for tcl roku tv

blackweb remote codes for philips tv

programming a blackweb universal remote

blackweb remote codes for vizio tv

blackweb 6 device universal remote

blackweb universal remote codes for lg tv

blackweb universal remote codes for emerson tv